ML4800CP【PDF 7/14 页】IC PFC CTRLR AVERAGE CURR 16DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录45

3页 4页 5页 6页 [7页]8页 9页 10页 11页

PRODUCT SPECIFICATION

ML4800

REV. 1.0.5 9/25/01

Functional Description

The ML4800 consists of an average current controlled,

continuous boost Power Factor Corrector (PFC) front end

and a synchronized Pulse Width Modulator (PWM) back

end. The PWM can be used in either current or voltage

mode. In voltage mode, feedforward from the PFC output

buss can be used to improve the PWMs line regulation.

In either mode, the PWM stage uses conventional trailing-

edge duty cycle modulation, while the PFC uses leading-

edge modulation. This patented leading/trailing edge modu-

lation technique results in a higher usable PFC error ampli-

er bandwidth, and can signicantly reduce the size of the

PFC DC buss capacitor.

The synchronization of the PWM with the PFC simplies the

PWM compensation due to the controlled ripple on the PFC

output capacitor (the PWM input capacitor). The PWM sec-

tion of the ML4800 runs at the same frequency as the PFC.

In addition to power factor correction, a number of protec-

tion features have been built into the ML4800. These include

soft-start, PFC overvoltage protection, peak current limiting,

brownout protection, duty cycle limiting, and under-voltage

lockout.

Power Factor Correction

Power factor correction makes a nonlinear load look like a

resistive load to the AC line. For a resistor, the current drawn

from the line is in phase with and proportional to the line

voltage, so the power factor is unity (one). A common class

of nonlinear load is the input of most power supplies, which

use a bridge rectier and capacitive input lter fed from the

line. The peak-charging effect, which occurs on the input l-

ter capacitor in these supplies, causes brief high-amplitude

pulses of current to ow from the power line, rather than a

sinusoidal current inphase with the line voltage. Such sup-

plies present a power factor to the line of less than one (i.e.

they cause signicant current harmonics of the power line

frequency to appear at their input). If the input current drawn

by such a supply (or any other nonlinear load) can be made

to follow the input voltage in instantaneous amplitude, it will

appear resistive to the AC line and a unity power factor will

be achieved.

To hold the input current draw of a device drawing power

from the AC line in phase with and proportional to the input

voltage, a way must be found to prevent that device from

loading the line except in proportion to the instantaneous line

voltage. The PFC section of the ML4800 uses a boost-mode

DC-DC converter to accomplish this. The input to the con-

verter is the full wave rectied AC line voltage. No bulk l-

tering is applied following the bridge rectier, so the input

voltage to the boost converter ranges (at twice line fre-

quency) from zero volts to the peak value of the AC input

and back to zero. By forcing the boost converter to meet two

simultaneous conditions, it is possible to ensure that the cur-

rent drawn from the power line is proportional to the input

line voltage. One of these conditions is that the output volt-

age of the boost converter must be set higher than the peak

value of the line voltage. A commonly used value is

385VDC, to allow for a high line of 270VAC

rms

. The other

condition is that the current drawn from the line at any given

instant must be proportional to the line voltage. Establishing

a suitable voltage control loop for the converter, which in

turn drives a current error amplier and switching output

driver satises the rst of these requirements. The second

requirement is met by using the rectied AC line voltage to

modulate the output of the voltage control loop. Such

modulation causes the current error amplier to command a

power stage current that varies directly with the input

voltage. In order to prevent ripple, which will necessarily

appear at the output of the boost circuit (typically about

10VAC on a 385V DC level), from introducing distortion

back through the voltage error amplier, the bandwidth of

the voltage loop is deliberately kept low. A nal renement

is to adjust the overall gain of the PFC such to be propor-

tional to 1/V

2, which linearizes the transfer function of the

system as the AC input voltage varies.

Since the boost converter topology in the ML4800 PFC is of

the current-averaging type, no slope compensation is

required.

PFC Section

Gain Modulator

Figure 1 shows a block diagram of the PFC section of the

ML4800. The gain modulator is the heart of the PFC, as it is

this circuit block which controls the response of the current

loop to line voltage waveform and frequency, rms line volt-

age, and PFC output voltage. There are three inputs to the

gain modulator. These are:

1. A current representing the instantaneous input voltage

(amplitude and waveshape) to the PFC. The rectified

AC input sine wave is converted to a proportional

current via a resistor and is then fed into the gain

modulator at I

. Sampling current in this way

minimizes ground noise, as is required in high power

switching power conversion environments. The gain

modulator responds linearly to this current.

2. A voltage proportional to the long-term RMS AC line

voltage, derived from the rectified line voltage after

scaling and filtering. This signal is presented to the gain

modulator at V

RMS

. The gain modulator s output is

inversely proportional to V

RMS

(except at unusually

low values of V

RMS

where special gain contouring takes

over, to limit power dissipation of the circuit

components under heavy brownout conditions). The

relationship between V

RMS

and gain is called K, and is

illustrated in the Typical Performance Characteristics.

3. The output of the voltage error amplifier, VEAO. The

gain modulator responds linearly to variations in this

voltage.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式